The adhesive is toughened for maximum impact resistance, along with excellent peel and shear strength. ES550 is ideal for bonding a wide range of materials including metals, ferrites, ceramics and composites.

This adhesive is toughened for maximum impact resistance, along with excellent peel and shear strength. ES558 is ideal for bonding a wide range of materials including metals, ferrites, ceramics and composites.

The high bond strength of this adhesive allows it to replace mechanical fastening, soldering or brazing. It has a rapid cure-25 minutes at 120 C and can be cured at temperatures as low as 90 C. Excellent adhesion to metal surfaces, composites and difficult to bond plastics (such as Nylon, PBT etc.). The high bond strength of this adhesive allows it to replace mechanical fastening, soldering or brazing.

ES569 has been designed to be non-sagging, allowing the product to be used in large gaps and on vertical surfaces. It is also ideal for bonding electronic components as it has high wet strength and is non-stringing and produces an excellent drop profile as well as withstanding solder reflow processes.

Excellent adhesion to metal surfaces, ceramics as well as composite materials. ES578 provides excellent thermal conductivity and bond strength. ES578 was designed for applications requiring heat dissipation such as bonding aluminum heat sinks to ceramic headers.

POTTING COMPOUND

ET515 is a semi-flexible toughened adhesive with good adhesion to a variety of substrates such as wood, metal, ceramics and some plastics and composites. It's a relatively fast curing epoxy; reaching handling strength in 20-30 minutes. It is ideal for bonding different materials where differential thermal expansion is anticipated.

Potting and coating, coating copper wire coils.

ET5401 forms tough bonds providing high peel resistance and high shear strength coupled with excellent resistance to high temperatures. ET5401 performance is enhanced by curing at high temperature or being exposed to high temperature (such as during paint-stoving).

ET5428 has been found to provide exceptional performance even at elevated temperatures. Permabond ET5428 has been specifically formulated for use in applications requiring toughness and high strength and shows special benefits in the construction of composite assemblies.

ET5429 has been found to provide exceptional performance even at elevated temperatures. It is ideal for use in construction of composite assemblies.

HH120 Threadlocker is an excellent general purpose threadlocker and sealant. It is used for locking bolts, nuts and screws that require permanent assembly. Its high viscosity allows for ease of use on coarse threaded fasteners. Cure is fast and reliable on steel, cadmium, zinc and other plated fasteners. Major use areas include machinery and equipment manufacturing. Additional uses include sealing pipe flanges and retaining worn bearings.

Prevents their movement relative to each other, eliminating wear, erosion, and pitting. HH040 cures to a tough cross-linked plastic that will prevent the corrosion of mated parts and provides excellent environmental and temperature resistance.

The liquid adhesive fills the air space between parts and upon cure which eliminates wear, erosion, and pitting. Permabond HL138 cures to a tough cross-linked plastic and provides excellent environmental and temperature resistance. Since Permabond HL138 can fill up the inner space, shafthub assemblies can be made with a clearance fit and eliminates an expensive press fit, while actually increasing the push out force. PERMABOND HL138 develops full strength quickly on a variety of metals and is used on high speed production lines.

Typically used for preventing vibration loosening of bolts, studs and cap screws. Full cure to a cross-linked plastic is achieved reliably and fast on steel and all common bolt platings. Additional application areas include machinery, equipment, and electric motor manufacturers.

Used for locking bolts, nuts and screws that require permanent assembly. Cure is fast and reliable on steel, cadmium, zinc and other plated fasteners. Major use areas include machinery and equipment manufacturing.This Threadlocker is an excellent general purpose threadlocker and sealant. It is used for locking bolts, nuts and screws that require permanent assembly. Cure is fast and reliable on steel, cadmium, zinc and other plated fasteners. Major use areas include machinery and equipment manufacturing.

This material cures in the absence of air between tight fitting metal parts. Cure is fast and reliable on steel, cadmium, zinc and other plated fasteners. It is used for locking and sealing bolts, nuts and screws that require permanent assembly. When cured, the material prevents loosening and leakage. *Permabond still recommends carrying out normal surface preparation to ensure consistent results. However, HM129 can provide superior performance compared with other sealing methods where there is presence of oil on surfaces. Cure is fast and reliable on steel, cadmium, zinc and other plated fasteners. It is used for locking and sealing bolts, nuts and screws that require permanent assembly. When cured, the material prevents loosening and leakage, Oil tolerant, Vibration resistant, Lubricates threads for easier assembly.

In the uncured, liquid state, the HM160 adhesive wets the metal surfaces, keying into all surface irregularities and fills the space between the mated parts.

It is best suited for cylindrical parts and where high temperature resistance is required. The high viscosity and thixotropic effect of the material allows for larger tolerances.

Permabond LH050 pipe sealant performs well on most metals, particularly steel and brass. It provides an excellent alternative to pipe dopes and pipe tapes for sealing pipe joints. It cures anaerobically when in contact with metal parts (as in a threaded pipe joint). When applied, LH050 dispenses as a smooth paste, filling the entire space between the threaded parts. It then cures at ambient temperature to form a solid plastic, completely sealing against hydraulic fluids, air, gases and chemicals. In addition, it locks the pipes, plugs or fittings against vibration loosening, tampering and variable temperature effects.

Cures to a tough cross-linked plastic that will prevent the corrosion of mated parts and provides excellent environmental and temperature resistance.

sealing and locking tapered metal pipe threads and fittings. It is ideal for stainless steel and other passive metal

Permabond LH056 forms an instant seal and once fully cured the seal will generally surpass the burst rating of the pipe. Permabond Pipe Sealants use anaerobic technology to prevent leaks in sprinkler systems. Used in fabrication and installation, Permabond Pipe Sealants replace pipe dope and sealing tapes with a complete and reliable seal even if pipes are not completely seated. They prevent corrosion and lock against vibration loosening. They do not remain a paste, like pipe dope, but cure to a solid plastic seal. Cure is initiated by the presence of metal and the absence of air. Permabond LH056 is FBC System Compatible. FBC System Compatible.

The added lubricity helps in seating the part even with an interference fit/ As such, it is used in heavy duty machinery e.g. compressors, hydraulics and construction equipment. When used on soft brass parts, the lubricity may be too high at times, thereby causing deformation of the part upon assembly. LH051 is also made flowable so that it can easily be applied with dispensing equipment. The particle size of the filler is very low, so that it can be used on most hydraulic systems without clogging hydraulic screens or valves. Permabond LH051 Pipe Sealant with PTFE provides an excellent replacement for pipe dopes and pipe tapes.

LH050 PURE pipe sealant performs well on most metals, particularly steel and brass. It provides an excellent alternative to pipe dopes and pipe tapes for sealing pipe joints. Another feature of PERMABOND LH050 PURE is the ability to seal pipes that have not been fully seated. In piping systems, pipe joints must connect with other pipes and in the direction in which the joint must face may not allow the pipe to be fully seated. LH050 PURE will seal even when the direction in which the pipe must face does not allow the complete seating of the threads. Anaerobic sealant will seal with simple hand assembly while still obtaining the seal of a fully torqued pipe joint.

A medium viscosity product for locking small threaded fasteners, such as screws and bolts or hydraulic fittings that might require disassembly. Due to its thixotropic viscosity, the liquid adhesive will not run away from the area of application. cures reliably and fast on steel, cadmium, zinc and other plated fasteners

SEALING PIPEWORK, HEATING, ETC. AGAINST FUEL, GASOLINE, WATER, OXYGEN

Its major benefit as related to other pipe sealants is that it is an unfilled resin that is compatible with hydraulic fluids. If the adhesive is accidentally spilled into the hydraulic system, e.g., squeezed out of the joint, it will be dispersed in the fluid. It contains no particles that can clog or foul hydraulic screens and valves. Thus it is used in very sensitive high pressure hydraulic systems.

It is capable of replacing a wide range of conventional gaskets, thereby offering potential for reduced stock holdings. By allowing surface to surface contact, load transmission can be improved. As the product does not shrink, creep or relax after curing, no bolt re-tightening is required. It has excellent chemical and high temperature resistance or up to 200 C.

Used for locking metal bolts, nuts and screws that may require disassembly for service and maintenance. Its medium strength allows disassembly with ordinary tools. Cure is fast and reliable on steel, cadmium, zinc and other plated fasteners. Major use areas include machinery and equipment manufacturing.

Ideal for use on a wide variety of substrate materials including metals, glass and composites. It is ideal for exterior construction applications as it has excellent resistance to weathering.

Excellent adhesion to Nylon, ABS, Polycarbonate and other plastics as well as a variety of different metals. The product can be cured in different mix ratios depending on the flexibility required in the final cured product. MT382 is self-levelling.

Thermal Interface Management. Soft and flexible. Thermal Conductivity 1.5W/(m.K)

Excellent adhesion to Nylon, ABS, Polycarbonate and other plastics as well as a variety of different metals. When cured, this adhesive is soft and flexible. Composite binding, Nylon, ABS, Polycarbonate & other plastics.

Ideal for use on a wide variety of substrate materials including metals, plastics and composites with excellent environmental and chemical resistance, Composites, Carbon Fiber & Interior Trim.

Designed for sealing/bonding & potting applications. Excellent adhesion to polycarbonate, ABS, nylon & other plastics as well as a variety of metal surfaces. Bonding heat sinks

Ideal for use on a wide variety of substrate materials and forms a very high strength structural bond with excellent environmental durability and chemical resistance. It has high peel strength and excellent impact resistance and can be used to replace rivets or welding to give a more lightweight, durable assembly. Use with Permabond Initiator 46.

Ideal for use on a wide variety of substrate materials including metals, plastics and composites. Its long pot life makes it suitable for covering large areas. It has excellent environmental and chemical resistance. (FOR INDUSTRIAL USE ONLY)

Its toughening makes it ideal for bonding dissimilar materials where differential thermal expansion and contraction could be an issue. It is easy to use with a delayed initiation, allowing accurate alignment of components. The strength develops quickly allowing clamps to be removed and a quick turnaround time when used in a production situation.

Magnet bonding, bonding heat sinks

This product was specifically designed to be non-corrosive to sensitive copper parts or other electrically conductive surfaces. The fast curing rate and rapid strength development of this material allows for increased production rate. Use TA459 with Initiator 41 (or Initiator 43 for use on plastics).

It has been developed to bond low surface energy plastics such as polypropylene and polyethylene with no primer or surface treatment required. It can also be used to bond a wide variety of other materials such as metals and composite materials and is ideal for bonding dissimilar surfaces.

Excellent optical clarity and resistance to yellowing make it ideal for bonding glass and crystal for a high quality finish. Its stability under ambient fluorescent lighting makes it suitable for use on glass bevels where some clean-up may be required after bonding.

TA4810 has excellent adhesion to as received metal surfaces, forming high strength bonds without surface preparation. It provides excellent durability and resistance to many common industrial solvents and fuels, as well as harsh environmental conditions. It cures rapidly at room temperature and its thixotropic properties allow for easy dispensing through static mixing nozzles, while maintaining good gap-filling and non-sag properties.

Excellent optical clarity and resistance to yellowing make it ideal for bonding glass and crystal for a high quality finish. It has excellent resistance to moisture and humidity , like Underwater lens bonding.

This material has excellent adhesion to a variety of plastics including polycarbonate. Permabond UV630 has very high shear strength, elongation and impact resistance making it ideal for applications that require substrates with different coefficients of thermal expansion. Excellent adhesion to a variety of plastics including polycarbonate. Very high shear strength, elongation and impact resistance making it ideal for applications that require substrates with different coefficients of thermal expansion, like polycarbonate lens bonding.

UV6160 has been specifically formulated to provide excellent optical clarity and enhanced transparency even when used in thick layers, in compression or in a heavily loaded joint

The optically clear / tack free formulation also makes this product particularly suitable for coating smart card microchips amongst various other applications. Its viscosity makes it suitable for encapsulation of electronic components and its high temperature resistance allows it to resist wave-soldering.

Ideal for coating electronics (such as conformal coating) to protect against environmental and vibrational damage. The optically clear, tack free formulation also makes this product particularly suitable for coating smart card microchips amongst various other applications. . Its low viscosity ensures an even, bubble-free coating and high temperature resistance allows it to resist wave-soldering.

PERMABOND® 105 is a low viscosity high purity cyanoacrylate adhesive. It is ideal for use on hard-to-bond plastics and rubbers such as natural rubber, EPDM and butyl rubber. For difficult rubbers.

Permabond® HH131 is a very high temperature resistant, high strength anaerobic threadlocker and sealant. This material cures in the absence of air between tight fitting metal parts. It is used for locking bolts, nuts and screws that require permanent assembly. This material is best suited for applications requiring high temperature resistance.

PERMABOND® 170 is a methyl cyanoacrylate adhesive. It is a single part, high viscosity liquid that will cure rapidly at room temperature when pressed into a thin film between parts. Permabond 170 will cure to a fixture strength in 15 seconds on most surfaces and strength development is rapid. The adhesive was designed specifically for the bonding of metal surfaces and provides excellent bond strength to steel, aluminum and most metal surface. The methyl cyanoacrylate will also adhere well to a wide variety of other materials including most plastics and rubbers. Permabond® 170 has been formulated to be less aggressive to sensitive plastic surfaces such as StyrofoamTM, polycarbonate and ABS. Gap Filling, Metal Bonding

PERMABOND® 101 is a low viscosity product useful in wicking or penetrating applications or bonding closely fitting parts. It is fast setting and suitable for use on plastics, rubber and metals. Cyanoacrylate adhesives are single component adhesives that polymerize rapidly when pressed into a thin film between parts. Permabond 101 CA is well known and highly used in all types of industrial applications. Wicking Viscosity

PERMABOND® 108 is an intermediate viscosity cyanoacrylate that is used to bond through intermediate gaps. It is fast setting and suitable for use on plastics, rubber and metals. PERMABOND cyanoacrylates the ideal adhesives for high speed production lines. Medium Viscosity.

PERMABOND 200 is a high viscosity product with good flow control useful in wire tacking applications or bonding components. It is fast setting and suitable for use on plastics, rubber and metals. Wire Tacking.

PERMABOND® 240 is a high viscosity product useful in large gap applications. It is ideal for porous substrates. It is fast setting and suitable for use on plastics, rubber and metals. Gap Filling.

Permabond® HH167 is a high viscosity gap filling silver paste, which can be used for repairing metal machinery parts. It is ideal for repairing worn shafts, broken threads, damaged keyways and splines. Permabond HH167 has excellent chemical and temperature resistance. NB. This adhesive is only suitable for gaps <0.5 mm and will not cure on the outside of a joint.

Permabond® HL138 is a single component liquid that cures only when in contact with metal parts and oxygen is excluded. The liquid adhesive fills the “air space” between parts and upon cure which eliminates wear, erosion, and pitting. Permabond HL138 cures to a tough cross-linked plastic and provides excellent environmental and temperature resistance. Since Permabond® HL138 can fill up the inner space, shafthub assemblies can be made with a clearance fit and eliminates an expensive press fit, while actually increasing the push out force. PERMABOND® HL138 develops full strength quickly on a variety of metals and is used on high speed production lines.

PERMABOND® 791 is a low viscosity, surface insensitive adhesive that will rapidly bond substrates with acidic surfaces such as wood and plated surfaces. Plastics, metals, ceramics and elastomers are also rapidly bonded. The fast cure minimizes the occurrence of frosting and fogging. Surface insensitive.

PERMABOND® 795 is a moderate viscosity, surface insensitive adhesive that will rapidly bond substrates with acidic surfaces such as wood and plated surfaces. Plastics, metals, ceramics and elastomers are also rapidly bonded. The fast cure minimizes the occurrence of frosting and fogging. Surface insensitive.

PERMABOND® 825 is a low viscosity modified ethyl cyanoacrylate suitable for applications where high temperature resistance is required. This material is fast setting and has good adhesion to rubber, metal and plastics. Permabond® 825 has excellent retention of strength during thermal ageing. High temperature.

PERMABOND® 737 is a toughened cyanoacrylate with improved impact and peel strength for maximum flexibility. Its increased temperature resistance and dark colour make 737 suitable for a wide range of applications. It bonds rapidly to a variety of surfaces including aluminium, steel (both zinc-plated and uncoated), plastics and rubbers. Toughened

PERMABOND® 790 is a low viscosity, surface insensitive adhesive that will rapidly bond substrates with acidic surfaces such as wood and plated surfaces. Plastics, metals, ceramics and elastomers are also rapidly bonded. The fast cure minimizes the occurrence of frosting and fogging. The wicking viscosity of this product makes it ideal for post-assembly application. Surface insensitive.

PERMABOND® 731 is a toughened cyanoacrylate with very good impact and peel strength when compared to a conventional cyanoacrylate. It bonds rapidly at room temperature and its viscosity is stable over the shelf life of the product. This provides consistent performance. The product adheres to a variety of surfaces including steel, aluminum, galvanized steel, plastics and elastomers. Toughened.

PERMABOND® 802 is a low viscosity modified ethyl cyanoacrylate suitable for applications where high temperature resistance is required. This material is fast setting and has good adhesion to rubber, metal and plastics. High temperature.

Fast Setting < 5 Seconds. PERMABOND® 910FS is the original 100%-methyl cyanoacrylate adhesive. It is a single part, low viscosity liquid that will cure rapidly at room temperature when pressed into a thin film between parts. PERMABOND® 910FS will cure to a fixture strength in 5 seconds on most surfaces and strength develops rapidly. The adhesive was designed specifically for the bonding of metal surfaces, and provides excellent bond strength to steel, aluminum and most metal surfaces. The methyl cyanoacrylate will also adhere well to a wide variety of other materials including most plastics and rubbers. Metal bonding.

PERMABOND® 735 is a toughened and flexible cyanoacrylate with very good impact and peel strength when compared to a conventional cyanoacrylate. It bonds rapidly at room temperature and its viscosity is stable over the shelf life of the product. This provides consistent performance. The product adheres to a variety of surfaces including steel, aluminum, galvanized steel, plastics and elastomers. Toughened.

PERMABOND® 922 is the original allyl cyanoacrylate adhesive. It is a single part, moderate viscosity liquid that will cure rapidly at room temperature when pressed into a thin film between parts. PERMABOND 922 will cure to fixture strength in seconds on most surfaces, and rapidly develops high strength with full cure obtained in 24 hours. The adhesive was specifically designed to meet the high temperature resistance required by certain applications. It provides excellent bond strength to steel, aluminum, and most metal surfaces. The cyanoacrylate will also adhere well to a wide variety of other materials including most types of plastic and rubber. In order to withstand high temperature environments, PERMABOND 922 was designed with a secondary curing mechanism that is activated at temperatures higher than 150°C (302°F). The procedure to activate this mechanism is as follows: 1) Parts are bonded and clamped at room temperature for four hours. 2) The clamped parts are then heated at 150°C (302°F) for two hours. 3) After the two hours, the bond will be thermally resistant up to 250°C (482°). High Temperature.

PERMABOND® 268 is a medium-high viscosity cyanoacrylate for large gap fill applications. Permabond® 268 provides faster set times and improved gap-filling capability compared to conventional cyanoacrylates. The adhesive bonds to a wide range of substrates including metals, ceramics, plastics and elastomers. It is excellent for bonding difficult-to-bond plastics such as polyacetals. It can also be used on passivated metal surfaces. General Purpose

PERMABOND® 919 is the original allyl cyanoacrylate adhesive. It is a single part, low viscosity liquid that will cure rapidly at room temperature when pressed into a thin film between parts. PERMABOND 919 will cure to fixture strength in 10 seconds on most surfaces, and rapidly develops high strength with full cure obtained in 24 hours. The adhesive was specifically designed to meet the high temperature resistance required by certain applications. It provides excellent bond strength to steel, aluminum, and most metal surfaces. The cyanoacrylate will also adhere well to a wide variety of other materials including most types of plastic and rubber. In order to withstand high temperature environments, PERMABOND 919 was designed with a secondary curing mechanism that is activated at temperatures higher than 150°C (302°F). The procedure to activate this mechanism is as follows: 1) Parts are bonded and clamped at room temperature for four hours. 2) The clamped parts are then heated at 150°C (302°F) for two hours. 3) After the two hours, the bond will be thermally resistant up to 250°C (482°). High temperature

PERMABOND® 941 is a low odour, non-fogging, nonfrosting alkoxyethyl cyanoacrylate. The reduced odour improves worker comfort. Unsightly fogging adjacent to bondlines, common with other cyanoacrylate adhesives on hot and humid days, is eliminated. The elimination of fogging improves the production rate of acceptable parts as well as their appearance. The adhesive is very stable and will provide optimum performance for one year when refrigerated. Low odor.

PERMABOND® 799 is a high viscosity cyanoacrylate that combines fast cure with the ability to cure through a large gap. Plastics, metals, ceramics and elastomers are also rapidly bonded. The fast cure minimizes the occurrence of frosting and fogging. This adhesive is particularly well-suited for used on porous substrates, since it fixtures before wicking into the surface pores.

PERMABOND® 801 is a low viscosity modified ethyl cyanoacrylate suitable for applications where high temperature resistance is required. This material is fast setting and has good adhesion to rubber, metal and plastics. High temperature.

PERMABOND® 820 is a low viscosity modified ethyl cyanoacrylate suitable for applications where high temperature resistance is required. This material is fast setting and has good adhesion to rubber, metal and plastics. High temperature.

PERMABOND® 943 is a low odour, non-fogging, nonfrosting alkoxyethyl cyanoacrylate. The reduced odour improves worker comfort. Unsightly fogging adjacent to bondlines, common with other cyanoacrylate adhesives on hot and humid days, is eliminated. The elimination of fogging improves the production rate of acceptable parts as well as their appearance. The adhesive is very stable and will provide optimum performance for one year when refrigerated. Low odor.

PERMABOND® 4C40 is a medium-high viscosity, medical device grade, cyanoacrylate for large gap fill applications.

PERMABOND® ES562 is a single-part epoxy adhesive which flows like solder when heated during curing. The adhesive has excellent adhesion to metal surfaces and composites. The high bond strength of this adhesive allows it to replace mechanical fastening, soldering or brazing. The adhesive’s low viscosity is such that it self-levels.

PERMABOND® 2050 is a flexible cyanoacrylate adhesive, exhibiting improved peel strengths when compared to other grades. It has excellent impact and vibration resistance, and is suitable for bonding dissimilar materials which could be subject to thermal shock or thermal cycling. 2050 is ideal for use on flexible or semiporous surfaces. It can also be used to bond silicone when used in conjunction with Permabond Polyolefin Primer (POP).

PERMABOND® 4C30 is an intermediate viscosity, medical device grade, cyanoacrylate that is used to bond through intermediate gaps. It is fast setting and suitable for use on plastics, rubber and metals.

PERMABOND® ET538 is a structural, room temperature curing epoxy adhesive that has excellent adhesion to a wide variety of surfaces such as wood, metal, ceramics and many plastic and composite materials. It exhibits good resistance to petrol, oils and water and has an extended cure time making it suitable for larger applications and batch production processes. Its thixotropic "non-slump" nature makes it suitable for gap filling or vertical application. Gap filling.

PERMABOND® 4C20 is an intermediate viscosity, medical device grade, cyanoacrylate that is used to bond through intermediate gaps. It is fast setting and suitable for use on plastics, rubber and metals.

PERMABOND® ET514 is a 1:1 mixable epoxy adhesive. It has excellent resistance to impact and vibration and is ideal for structural bonding of metal, wood, composites and certain plastics. Its rapid cure speed coupled with its structural strength makes this adhesive suitable for a wide variety of applications. ET514 is high strength and has excellent environmental durability.

PERMABOND® ET505 is a two-part, 1:1 mixable epoxy adhesive. ET505 is a semi-flexible toughened epoxy adhesive with good adhesion to a variety of substrates such as wood, metal, ceramics and some plastics and composites. Permabond ET505 forms tough bonds providing high peel resistance and high shear strength. The extended work life of this product allows for adjustment and makes it more suitable for larger applications.

PERMABOND® ET510 is a two-part, 1:1 mixable epoxy adhesive. ET510 is a semi-flexible toughened epoxy adhesive with good adhesion to a variety of substrates such as wood, metal, ceramics and some plastics and composites. The product cures rapidly at room temperature reaching handling strength in 2040 minutes. Once cured, Permabond ET510 has good chemical and environmental resistance.

PERMABOND® 4C10 is a low viscosity, high purity, medical device grade, cyanoacrylate adhesive. It is ideal for use on hard-to-bond plastics and rubbers such as natural rubber, EPDM and butyl rubber.

PERMABOND® ET536 is a two-part, 1:1 mixable epoxy adhesive with good adhesion to a variety of substrates such as wood, metal, ceramics and some plastics and composites. Permabond ET536 forms tough bonds providing high peel resistance and high shear strength. The extended work life of this product allows for adjustment and makes it more suitable for larger applications. Non-drip Rheology. Gap filling

PERMABOND® 2010 is a thixotropic, fast-setting cyanoacrylate particularly suitable for use on vertical and porous substrates. This material can be used on metals, plastics, elastomers, ceramics, and wood. High viscosity.

PERMABOND® ET5422 is a thixotropic two-part adhesive with excellent resistance to impact and vibration. Tough when cured. The controlled flow properties as well as its ease of mixing and application, enables the adhesive to be used where gap filling is required. Permabond® ET5422 has been found to provide exceptional performance even at elevated temperatures. Permabond® ET5422 has been specifically formulated for use in applications requiring toughness and high strength.

PERMABOND® TA4207 is a 2-part, 1:1 toughened acrylic adhesive. It can be used to bond a wide variety of materials including metals, plastics, composites, ceramics, wood and other substrates. The adhesive can provide excellent shear strength on many substrates with little surface preparation.

PERMABOND® TA4631 is a 2-part, 1:1 no odour* acrylic adhesive. It has been developed to bond low surface energy plastics such as polypropylene and polyethylene – with no primer or expensive surface treatment required. It can also be used to bond a wide variety of other materials such as metals and composite materials and is ideal for bonding dissimilar surfaces. This product is similar to TA4630 but does not contain micro beads making it suitable for joints with smaller gaps. *no perceptible odour detected by testing panel members

PERMABOND® TA430 is a structural acrylic adhesive designed primarily for bonding metals, ferrites, ceramics, wood, and some thermoplastics. This adhesive may be used in a variety of structural bonding applications due to its versatile performance capabilities. Permabond TA430 provides high strength while maintaining excellent flexibility, resulting in tough, durable bonds with outstanding impact and peel resistance. Handling strength is achieved in a few minutes at room temperature by using Permabond Initiator 41.

PERMABOND® MT3809 is a 10:1, two-part, modified epoxy adhesive designed for potting applications. It has excellent adhesion to Nylon, ABS, Polycarbonate and other plastics. When cured, this adhesive is soft and reasonably flexible. Its low viscosity makes it suitable for potting intricate parts.

Permabond MT3836 is a flexible, thermally conductive, fire retardant adhesive ideal for electronics and e-vehicle battery applications. PERMABOND® MT3836 two-part, modified hybrid silane polymer adhesive designed for sealing and bonding applications. It has excellent adhesion to polycarbonate, ABS, Nylon and other plastics as well as a variety of different metals. The cured adhesive has been designed to meet the fire retardancy requirements of UL94 V-0.

Self-Leveling. PERMABOND® MS359A GREY is a single-part, moisture curing MS polymer adhesive. It is ideal for use on a wide variety of substrate materials and is ideal for potting and sealing electronic components, sealing filters, and bonding large metal panels (such as transport containers, air conditioning ducts etc.). Easy to apply, and can be painted after cured.

PERMABOND® TA439 is a two component structural acrylic adhesive designed primarily for bonding metals, ferrites, ceramics and some plastics. The typical fixture time of is 20-40 seconds. The fast fixture time of TA439 makes it an ideal adhesive for high speed production lines. This product provides high strength, tough, durable bonds with good impact resistance and performs well in drop tests.

PERMABOND® TA4820 is a 2-part, 1:1 toughened methacrylate adhesive designed for bonding thermoplastics, thermosets, metals and composites. TA4820 has excellent adhesion to as received metal surfaces, forming high strength bonds without surface preparation. It provides excellent durability and resistance to many common industrial solvents and fuels, as well as harsh environmental conditions. It cures rapidly at room temperature and its thixotropic properties allow for easy dispensing through static mixing nozzles, while maintaining good gap-filling and non-sag properties. The long fixture time allows for accurate alignment of larger components.

PERMABOND® TA435 is a structural acrylic adhesive designed primarily for bonding metals, ferrites, ceramics and some thermoplastics. This adhesive may be used in a variety of structural bonding applications, due to its versatile performance capabilities. TA435 provides high strength while maintaining excellent flexibility, resulting in tough, durable bonds with outstanding impact and peel resistance. Handling strength is achieved in a few minutes at room temperature by using Permabond Initiator 41.

PERMABOND® TA4590 is a structural acrylic adhesive designed primarily for bonding metals, ferrites, ceramics and some thermoplastics. This product was specifically designed to be non-corrosive to sensitive copper parts or other electrically conductive surfaces. TA4590 is a no-mix system which has a 15-30 sec. fixture time on metal surfaces when used with Initiator 44.

PERMABOND® TA440 is a two component structural acrylic adhesive suitable for bonding metals, glass, wood, ferrites, ceramics and some rigid plastics. This adhesive may be used in a variety of structural bonding applications due to its versatile performance capabilities. Permabond TA440 provides high strength while maintaining excellent flexibility, resulting in tough, durable bonds with outstanding impact and peel resistance. Handling strength is achieved in a few minutes at room temperature.

PERMABOND® TA436 is a structural acrylic adhesive designed primarily for bonding metals, ferrites, ceramics and some thermoplastics. Permabond TA436 is a no-mix system which obtains handling strength 1-3 minutes when the adhesive and the Initiator 43 come in contact. Permabond TA436 offers high shear and impact resistant bonds and improved high temperature resistance.